Custom ecu

...at all four corners along with custom-built 15″x10″ steel wheels with Thunderbird center caps and stainless steel beauty rings. A complete set

...camshaft and lifters, an Eddie Motorsports serpentine pulley system, a Mattson’s aluminum radiator and air conditioning condenser, and a custom...

...a Ford 8″ rear axle as well as a Chevrolet bellhousing, flywheel, clutch, and pressure plate. Engine modifications includef a MegaSquirt II ECU...

...200 miles since installation. A RetroSound stereo is linked to Pioneer 5.5″ and 6″x9″ speakers in custom panels as well as a 12″ subwoofer.

...Additional modifications include a Holset HX50 turbocharger, a Mishimoto 4â? ³ intercooler, Bosch coil packs, an ECUmaster EMU Black ECU...

...clutch cylinders. The cockpit features a Sparco Steering wheel, Bride Low-Max bucket seats, a fully custom dash, and a Wilwood pedal assembly.

...features Dirty Dingo front accessory mounts, an orange and black top cover, an aftermarket engine wiring harness, and a factory-style GM ECU...

...custom auxiliary input as well as an onboard computer, cruise control, and air conditioning. A Husco armrest was installed along with a...

...includes Style 21 wheels with â? Throwing Starâ?  covers, heated power-adjustable front seats, air conditioning, an onboard computer, a custom...

...a Safety Devices fire suppression system, an Exige-style driverâ? S racing seat, five-point harnesses, an AIM data acquisition system, ECU...

...custom LED interior lighting. An Alcantara-wrapped MOMO steering wheel frames a Nismo 260-km/h speedometer and an aftermarket Kakimoto...

...later-model seating, a Spultronix digital dash display, a Nardi steering wheel, AutoMeter instrumentation, and a custom audio system.

...that has been powder coated prior to installation. This truck runs and drives like a beast! The interior is all new and we installed custom...

...done approximately six years ago. A complete mopar 5.7hemi drivetrain with less than five thousand miles was procured, engineered, wired, ecu?...

...ECU. The engine was subsequently rebuilt and resealed before being installed. The seller notes that the car has been driven around 1,300...

...Custom center-outlet straight pipe exhaust systemCarbon fiber RS heater tubeB&B; front oil coolerElephant Carrera fender cooler with...

...a custom stainless steel exhaust system, a black soft top, Dakota Digital gauges, replacement seats, and a Pioneer infotainment system.

...cylinder and brake booster (OEM) LS-Based 5.3 L engine Rebuilt 4 Speed and Transfer Case Factory ECU with custom Tune OBD II Port functional

Hummer H1 completely rebuilt by Predator in California complete with a Duramax 6.6 Diesel Motor, Alison Transmission, Custom Transfer Case...

...car is equipped with the following: Garret GT28RS turbocharger, TiAL 44mm blow-off valve, 550cc fuel injectors, 034Motorsport EFI Stage 1 ECU...

...transmission and an NP241 transfer case. The 6.0-liter L96 Vortec V8 features an iron block and aluminum cylinder heads as well as a custom...

...“Rodman” highboy roadster was built by Rod Palmer of Arizona Street Rods in the 1990s and features a Wescott fiberglass body and a custom-built...

...parts. Ron Davis 4 courseAluminum radiator. Dual electric fans. Set up on the ECU/computer, Vintage air II/ AC &Heat Aluminum 7qt oilpan.

...cylinder and brake booster (OEM) LS-Based 5.3 L engine Rebuilt 4 Speed and Transfer Case Factory ECU with custom Tune OBD II Port functional

Ford Coyote Gen 2 5.0l crate engine with OEM harness and ECU 3-link suspension setup Breeze automotive control arms 8.8 3.55 ratio rear end...