33 used cars in Port Crane

...hydraulic cam shaft. It has the original heads on it that have been ported with hardened seats installed and stainless steel valves with crane...

...rear bench seatshigh performance 460 cubic inch block dive-6015-a2b m-6642-a101 motorsport oil coolerd2oe-a-police interceptor heads port...

...body. It has complete custom paint with custom flames. This car has been at the ISC Street Rod Nationals and judged. It has a 406ci Tuned Port...

...eye brow. The harmonic balancer is a Streetdampr by Fluiddampr. The heads are OE closed chamber, with all new single groove valves, a mild port...

2015 Frieghtliner M2 112 Medium Duty Regular Cab RWD DRW Crane Service Body Truck, Cummins ISL G 8.9L I6 250hp CNG Hi-Torque Engine, Allison...

...110octane. The engine has been half filled with hard block and isbored 100 over, ARP studs and connecting rod bolts, GM forged steelcrank, Crane...

...Port) Dominator intake. 2 inch headers with 3 inch collectors. Demon 1050 carb. The engine has 12.9 to 1 compression and is internally...

1970 351 Cleveland 4V (same motor Ford used in the Pantera). Crane Roller rockers/ locks. Hydraulic Lunati Vodoo Series Cam. 4V closed chamber...

...Factory spec Crane solid liftercam, roller timing chain and a set of headers. Correct 4 coreradiator, reproduction hoses and clamps. Proper deep

...octane. The engine has been half filled with hard block and is bored 100 over, ARP studs and connecting rod bolts, GM forged steel crank, Crane...

...Crane Ignition system and Cyclone AR-1 headers. It runs cool with a 4-core aluminum radiator, dual electric fans, and new polished aluminum...

...a full Crane roller cam set-up, Melling high volume oil pump, Chevy Bow-tie rectangular port heads, Crane roller rockers, ARP fasteners, an

...port NOS system with fogger& purge Dyno without nitrous at: ·781 HP @ 6500 ·Torque 728 @5200 Has run 8.8 seconds @152 MPH Dyno sheet and...

...Crane Cams Stud Mounted Aluminum Roller Rockers Custom Billet Aluminum 6-Rib Serpentine Accessory Drive Hydraulic Rack and Pinion Power...

...port fuel injection. It's a monster package that's also supported by the right pieces, including upgraded pulleys, a full MSD ignition...

...460 crank to when it was rebuilt about 3000 milesago. This engine has TRW forged. 060 pistons (472 cubes), Crower level 2 cam, adjustable Crane...

...cloth cover and cart for hardtop. The 427 cu. IN. Engine is a numbers correct 1966 4 bolt main block, aluminum manifold, holly carb. Square port...

...460 crank to when it was rebuilt about 3000 milesago. This engine has TRW forged. 060 pistons (472 cubes), Crower level 2 cam, adjustable Crane...

...port intake manifoldHolley fuel pressure regulator with liquid filled gauge New-ish battery IPD 4-1 headersNew-ish exhaust New water pumpNew...

...It has a. 030 over 454 roller motor; K & N, Edelbrock carb, aluminum GM bowtie intake, Crower stainless steel roller rockers on large oval port...

...rockers, and port-matched aluminum heads. It inhales deeply with an Edelbrock Air Gap with a Demon 650 CFM four-barrel carburetor on top. And

...Crane XR700. Alternator. Electric fuel pump new wiring harnesses. Dual exhaust (straight extractors). Aluminum oil pan. Aluminum valve covers...

...Crane Cams Stud Mounted Aluminum Roller Rockers Custom Billet Aluminum 6-Rib Serpentine Accessory Drive Hydraulic Rack and Pinion Power...

...performance parts, and many of the specifications are as follows: GM 010 Block bored. 030 over ARP Head Bolts 2.02/1.60 Stainless Valves Crane...

...coupe street rod in a beautiful Corvette Red powered by a 454 cubic inch big block Chevrolet with vintage polished aluminum GM rectangular port...